Dynaflex Chrome Z Series Center Spool With Taper Lock Extension
*Fitment below is what is most common but you must measure your exists center spool to determine length needed.
*Center Spools designed to work with Dynaflex brand exhaust. Cannot guarantee proper fitment with other brand exhaust.
- Middle Spool Piece With Taper Lock Extension O.D.
- Chrome Finish
- Available With Built-In Silencer (Select Above)
- 48" Length: Kenworth W900A, W900B
- 52" Length: Peterbilt 379 (Early 2003 & Older), Kenworth W900L, Freightliner FLD, Western Star
- 55" Length: Peterbilt 359, Peterbilt 379 (Late 2003 & Newer)
- Sold Individually
- High Quality Dynaflex Product
Dynaflex's intelligent Taper Lock design at the top joins with a standard OD pipe which gives a seamless look to your exhaust stacks. Ignore the ugly bulges of expanded ID stacks and upgrade to a Dynaflex Exhaust
If you should need additional Truck Parts and Accessories, please don't hesitate to call our toll-free number 1-888-888-7990
Dynaflex Products warrants the products or components parts sold conform to the specifications and physical descriptions contained in any or all Dynaflex Product literature, including but not limited to product catalogs, flyers or individual sale sheets. The Limited Warranty appearing on any or all Dynaflex Product literature is exclusive and is in lieu of all warranties whether written, oral or implied, including any warranty on fit or purpose.
This warranty applies to and is for the benefit of the original purchaser only.
Dynaflex Products are warranted for ne year from date of purchase with proof of purchase only. If proof of purchase cannot be supplied, then the warranty will be from date of shipment, against defect in material and workmanship. This warranty does not apply if the defects are due to accident, neglect, corrosive environments or other abnormal service conditions.
Neglect, corrosive environments, and abnormal conditions:
If chrome is exposed to rock salt on snowy road conditions for extended periods of time it will corrode, crack, chip, and peel the chrome. Chrome needs to be cleaned intermittently to remove any corrosive materials. If your truck has an engine that is 2007+ the AK systems are the only systems Dynaflex Products can warrant. 07+ engines with a DPF will run very hot (1200 degrees), the AK system is the only product that can handle that heat. If you have on 07+ system that was factory fit with a DPF, but the DPF has been removed it will void your warranty for your chrome. 2007+ engines have engine programming that makes them burn rich, if you remove the DPF system, un-combusted Hydrocarbons will discolor and harm the chrome, Dynaflex Products is not responsible for holding warranty on trucks that changed from their OEM exhaust design. 2010+ exhaust systems contain selective catalytic reduction systems that use DEF (ammonia) to neutralize NOX. Ammonia is an environment contaminant and can discolor your chrome if not cleaned. SCR systems may let small amounts of aqueous ammonia out the tailpipe. Cleaning the tips of your tailpipes will ensure your chrome lasts. DPF/SCR systems that are improperly that improperly maintained may void your chrome warranty. DPF systems need to be cleaned every 1,000-1,500 operating hours. If not temperatures in your exhaust system may reach levels that chrome cannot withstand.
Dynaflex Products innovated the 3 piece (Z-series) stack design and can only warrant complete z-series parts. We cannot warrant, for example, a Dynaflex Products elbow used with an import spool. We cannot guarantee the taper-loc joint will seal correctly if not using complete Dynaflex Products z-series kits with Dynaflex Clamps.
This warranty is limited to the provisions shown and Dynaflex Products does not assume responsibility for the cost of removal or installation of the product or any consequential expense.
Should the product appear to be defective within the warranty period, it should be returned to the dealer that the parts were purchased from. If their inspection confirms that the product failed as result of material or workmanship, and Dynaflex Products accepts responsibility the product will be replaced at no charge.
A written copy from Dynaflex of the Return Good Authorization (RGA) is required prior to returning merchandise. All returns must be shipped prepaid to Dynaflex, Commerce, CA and have the RGA number clearly and boldly marked on the outside of the shipping box(s) or the shipment may be rejected. An RGA is only valid for 30 days after being issued if received after this time frame the shipment will be rejected. All shipping costs, including duties, brokerage fees, drayage, etc., will be at purchaser's cost.